nexus phone case This is a topic that many people are looking for. drustvosns.org is a channel providing useful information about learning, life, digital marketing and online courses …. it will help you have an overview and solid multi-faceted knowledge . Today, drustvosns.org would like to introduce to you DIY Wood Backed Phone Case – iPhone and Android Nexus 5. Following along are instructions in the video below:
“Time. I m going to be making these wooden phone cases well actually they re re just plastic cases. Nwith veneer glued to the back. But in my opinion that the better way nto do it not only do entirely would cases end up nbeing.
Quite chunky. But they re also extremely difficult to nmake. I ll be showing you how to make this niphone 4s case. Because this technique works so well with phone cases with an entirely flat nback.
But i ll also be experimenting with a nsecond phone case. Which doesn t have a particuarly flat back. And that s for the nexus. 5.
Which is the nphone..
I own which i thought was also worth giving a nshot unless for some reason you re desperate nto get your smartphone covered in sawdust and glue the first thing you re going nto want to do is make a substitute phone like this out of wood as a base for these wooden ncovered phone cases. I m using these very cheap plastic cases which i picked up on ebay for less than ntwo pounds each i m starting off by scuffing. The nback of the phone case to provide a better surface for the glue to adhere to i would nactually recommend that you do this step by hand as using the belt. Sander as i m ndoing here can tend to create quite a bit heat.
Which could potentially damage your thin nplastic case. I m cutting out the walnut burl veneer nwhich. I ll be using with a stanley knife a straight grain veneer will work even. Better now.
I m ready to go ahead and glue. The nveneer to the plastic case. I m using some five minute epoxy for nthat. Which should just about give me enough working time if i m quick about it it s at this point.
I realize i m about nto glue..
My substitute phone to the inside of nthe case. So i quickly use some masking tape to ncover up where the holes in the back of the case are i m wrapping the case as tightly as i ncan in masking tape which i m hoping will apply pressure to nthe curved edges of the case as well as to the back instead a masking ntape you could also try using lots of elastic bands and glueing the iphone case is much neasier as i can just use a couple of clamps to apply a small amount of pressure with the glue dry now on these cases. I m nready to move on to what will be the most boring stage in this entire process and that s nremoveing. All the squeeze out and just ncleaning up the edges to where it looks nice and neat.
And i ve actually kinda started the niphone case already so i m about to do some work non. The nexus case. I ve already gone ahead and ncut away the excess on the iphone case and that worked out pretty nicely. It s nnot.
Quite as simple for the nexus case because of the curve around the sides. I won t just be able to trim along the nedges. There s also some areas of quite nquite poor adhesion. What i thought i would do instead is using this rule and a stanley knife.
Again i m going to trim along the edge..
Where nthe very beginning of the curve starts and i think that will look alright just by cleaning up those edges. It s nalready looking a lot better than it was if you don t have a bunch of power tools nat your disposal. You can certainly use hand tools to do nthe. Same thing here i m using a cabinet scraper to clean nup.
The squeeze out glue on the iphone case ni m using this multi tool. Although you might know as a dremel tool to cut out the little camera hole in the nback of the cases with all that sanding done i m napplying a few coats of finishing oil to the veneer. I think you certainly could try using nlacquer or something like that but i m a bit concerned that a film finish like that nwould just get to scratched from day to day use added to the fact nthat. I don t really have the time available to me to apply finish like nthat.
I m happy to use the finishing on oil as i expected the iphone 4s case. Did ncome out a lot better than the nexus. 5 case. But nthat being said.
5 case. Did still come out a lot better than i nthought. It would so i m very please with the finished nresult. I titled this video a diy project.
Because i expect you to be doing nthis project yourself. If any of you end up with some nfinished phone cases send me some pictures over on facebook. There s some links ndown in the description for that it would be great to see what you come nup with as always be sure to like share comment and subscribe before you go. ” .
Thank you for watching all the articles on the topic DIY Wood Backed Phone Case – iPhone and Android Nexus 5. All shares of drustvosns.org are very good. We hope you are satisfied with the article. For any questions, please leave a comment below. Hopefully you guys support our website even more.